- 348 & 409's getting more expensive?
- New stock water pump
- Coincidence or just plain luck?
- 6x2 or 4x2 or 2x4 or....?
- Gasket Kit
- pilot bearing?
- Blower intake
- Three 2's on a 409?
- August Hot Rod Mag, Page 94
- 348 Crank Balancer/Damper Install?
- PCV Advice
- 348 Head Date Code Question
- Edelbrock heads
- Texas trash 409
- Weird Valve train Prob on 348
- Edelbrock 409/4bbl
- Broken Dristrbutor Rotor
- Out for a drive in the country
- Aubrey SuperChevy August 2008
- 409/425 Fuel Mileage
- Shaving Cam Bearings
- Ignition question: Ronnie: chime in please
- Anyone Near sioux falls SD?
- MSD dist. W/ Vintage Tach???
- how tight are dougs headers
- 817 heads and intake
- just a little tease
- Help with adjusting Carter aftermarket 4 barrel.
- 348 cam choices
- 379 Heads and HP valves: What Springs?
- Help me educate a few "knowitalls"
- 348 cylinder notch
- camshaft and intake recomendation for 348 stroker
- Carb replacement
- cooling system rust inhibitor recommendation
- Muscle Car Review
- 348: Mains "good", rods need .030 under
- There Is A Different Mount For A 409 Vs 327???
- 6x2 Driveability
- 409 trivia question
- 1961 623 block
- Jardine Update
- More 409 Trivia
- 409/425 cam suggestions.
- 409 Running Rich
- 348 Cam Bearing Interchange?
- mini starter #
- More Ink or Just who is Ray Borba???
- 500 Mile trip a big success
- Flow testing intake?
- 409 craigslist
- 348 Valve Cover Wire Looms
- Carter AFB specs
- Connecting rods and valves
- Remote oil filter - what to use?
- 817 or 333 Heads for 348 280HP
- Weight of Flywheel - Heavier with weaker engine???
- What are the best headers to my 409 64 Impala?
- Well I did it
- Deep Groove Pulleys and Idler
- 1960, 3-series rear: How far can I go with gears?
- Edelbrock flow numbers
- 333 Heads
- Buying Truck 409
- Bending Push Rods
- New Pictures
- need help with brake booster brackets
- MaxChevy 409!!
- Is this saveable????
- something for you all to look at
- Carb CFM
- rebuild distributor
- 348 Sump Plug Thread Pitch????
- Valve Covers Back From Chrome Shop
- gabriel-cestaro - MORE INFO!!!
- 409 oil pan info
- What to buy for your wife's birthday!
- Cut Outs /hushpower/flowmaster
- Coil Springs
- 348 radiator for a rod/SBC flywheel..
- Rearend question
- Cross Ram hood clearence
- 348 timing
- 62 Belair 409 Conversoin
- Mystery 409 Casting Number
- Horsepower TV
- 60Impala4Dad convt
- Pic's of my 62
- fun pictures
- New Edelbrock Heads
- got any idea? possible 409
- 348/409 4 barrell intakes
- K&N air filter- huge hp gain !!!!
- Dragonslayer
- 4" Stroker Dyno Report
- The Ford Mercury-Edsel-Lincoln (MEL) Engines
- T-106 Ha ?
- 1961 FJ 340HP 348 Block Characteristics
- 409 Aluminum Intake 3814678 Port Size?
- rear oil seal leak
- 540 Intake manifold
- Hydraulic lifters
- torque plates
- 348: Plate between flywheel and block?
- Stef's oil pan question
- 9 Months And Its Alive JOE STARTS HIS FIRST 409 AT THE AGE OF 8
- Head Gasket Question ?
- Back Carb Making A Weird Sounds?
- I am getting advanced here.....
- stroker parts prices
- 409 ID Numbers
- v-belt arrangement
- opened 3x2 intake
- Custom PVC
- "High port" intake gaskets
- engine orange
- Red Sled gets a 409
- 409 Exhaust Manifolds vs Headers
- Blown 409
- 409 Crank Part #
- 348:specs & Part #
- New Covers
- Long haul with a 409 powered car
- 333 truck heads
- Flow numbers for you guys 690 vs E head
- Gathering parts
- 881 intake manifold on 333 heads
- Exhaust Manifold Info
- Hooker headers-one piece?
- 409 video
- Show Cars 6 duece set up
- Tore down my 348, looks to be a virgin in good shape.
- Another make of 348-409 piston is coming!
- No Oil At Sending Unit
- Another cooling option???
- exhaust manifold gaskets
- Cast date ???
- 32 Ford with a 409
- Edelbrock Heads
- modern technology
- Camshaft spec
- 409 in a 1935 chevy
- Suffix code
- 409 1x4 intake
- Hot Rod Mag & Edlebrock 409 heads
- Was factory installed AC an option w/409 or a RPO?
- Which clutch fork for Lakewood on 348?
- Just got 409 back from machine shop.
- Valve clearance
- Block mounted 3-bolt starter?
- Camshaft Replace
- Induction madness
- Will this balancer work?
- On The Ground And Running
- Help ID 409 Piston, GM# 3819377
- Petronix Coil on a 409
- Header pipe size recommendations please
- 409 at the top of the page
- Machine Shop
- Porting my virgin 690..................
- 409 crank how strong?
- Storing a rebuilt engine
- coil for HEI
- 2G conversion from Show Cars
- 348 head gasket
- Bore and Stroke Ratios
- spark knock
- Don't think I have a 348
- need help figureing hp
- Gettin her done!
- flywheel identification