Home
Forums
New posts
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Birthday calendar
Donate
Products
Calendar
Log in
Register
What's new
Registered members
Current visitors
Birthday calendar
Menu
Log in
Register
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
S
Schack348
Member
·
53
·
From
Athol New York
Joined
Feb 27, 2024
Last seen
May 6, 2024
Messages
12
Reaction score
13
Points
3
Latest activity
Postings
About
S
Schack348
replied to the thread
New here hi everyone
.
Don sorry to bother you I found a cam on the Howard’s cam site hrc 130101-12 is this the correct one thanks again
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
A lot of thanks Don Jacks I will see if I can find the build sheet info what was put in give you more specific info tremendous amount of...
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Feb 28, 2024
S
Schack348
reacted to
Don Jacks's post
in the thread
New here hi everyone
with
Like
.
hrccl-1305010-12 Howards Cams from Competetiox Products,keep the rpm below 6000 if running cast 10.5 pistons and stock rods.
Feb 28, 2024
S
Schack348
reacted to
327's post
in the thread
New here hi everyone
with
Like
.
Schack348 :welcome2
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Scott Hall thank you very much for the direction I know some but not a pro on the 348 nice to have all the people here willing to...
Feb 28, 2024
S
Schack348
reacted to
scott hall's post
in the thread
New here hi everyone
with
Like
.
No if pads aren't there, there is a drop down from deck surface. Yes drill and tap holes in heads for a threaded plug if it's not flush...
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Scott and you drill 1872 block without pads I don’t think so but just asking
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
I have read Scott that I can plug the holes and it would be fine what do you think tap and plug them
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Feb 28, 2024
S
Schack348
reacted to
scott hall's post
in the thread
New here hi everyone
with
Like
.
Does the block have the pads for the cooling holes. If not you’ll need to plug those wholes in the heads of your choice. Be it aluminum...
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Don Jacks it’s been quite a while since I went threw the motor they are I think at least 10.5 I remember motor was bored 90 over because...
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Muphdog thanks my block is the early1872 I’m assuming with no holes for spark plug coolers it has the 2791 heads also suggesting that I...
Feb 28, 2024
S
Schack348
replied to the thread
New here hi everyone
.
Feb 28, 2024
S
Schack348
reacted to
Don Jacks's post
in the thread
New here hi everyone
with
Like
.
, Bob Walla Racing for your heads.What piston are you using?I need to know that to help with cam selection. :welcome2
Feb 28, 2024
Loading…
Loading…
Home
Members
Top