It is good to do it; it gives you a close up of everything underneath. I have been marine technician for roughly 25 years; part time job that went with my full time job, which is now my full time job! One thing I learned from the old salts was to look at everything...As Joe and Alice can't pull over to the side of the road and dial #77, pop a flare pattern and wait for a rollback in a boat.I'm getting ready to redo my rear suspension very similar to yours, I was going to add the Global West panhard. The only difference is I am going to add the second upper control arm.
In my opinion, you have the perfect car to work on, no body or interior work, which generally requires mucho experience, (to do it correct anyway). The mechanical stuff is a little easier to tackle, especially with your knowledge. It looks like your ready to start cruzin'. I ran into a issue today with adding the additional UMI upper control arm. They came with two brackets that bolt to the frame with the upper control brackets and are supposed to strengthen the frame mounts. I have them installed (the way I think they are designed), but nothing makes any sense to me, as I can't figure out how they are supposed to work, or be installed correctly for that matter. I must be doing something wrong. Attached are some pic's that hopefully someone has experienced this or knows how they work. The first picture shows the parts and second picture show them installed the way I think they are supposed to be installed. It seems like they should be welded to the frame sides, but their not even remotely close.
I bought them @ Show Cars and could ask them on Monday but I got ants in my pants!
They go this way, just finished assembling this rear end after powder coating(no pictures after the powder coating and assembly yet -if you need some I can take closeups) .
The welding is not completed in the pictures. The passenger side of this 62 SS 409 convertible frame (mine and a friends 409 restoration) had been pulled off the frame rail
and had to be repaired along with adding the braces to botht sides.
The last picture includes my adjustable UMI daul upper rear control arms on my 62 SS 409 convertible completed frame that does not have the frame braces.
PaulView attachment 34448 View attachment 34449 View attachment 34450 View attachment 34451 View attachment 34452
Last year I did the engine and trans, then took a 2400 mile test drive to Kansas and everything was good there.. Lol. This year I figure I'm gonna hammer it pretty good so I thought I should fix the rear end before something bad happens. I ordered the axles last week and I plan on getting the Global West stuff at Summit since I live close enough to go pick it up. I like those UMI frame brackets. Are those available separate or do you have to buy the arms too??It is good to do it; it gives you a close up of everything underneath. I have been marine technician for roughly 25 years; part time job that went with my full time job, which is now my full time job! One thing I learned from the old salts was to look at everything...As Joe and Alice can't pull over to the side of the road and dial #77, pop a flare pattern and wait for a rollback in a boat.
With that mentality, I rebuilt and replumbed the entire brake system; added front disc brakes purchased a very nice kit from 58 delivery as suggested by one of my other mentor on the site. Replumbed the entire fuel system, all new hardware. Rebuilt the entire rear on the bench, including the third member; basically went through the chassis. When I started two years ago, I pulled the engine and transmission to freshen it up. Wound up rebuilding just about everything mechanically as the guy that originally restored the car 25 years ago did a great job. The guys in between sort of let it go and negelcted it mechanically. During the process I slowed down and looked at everything. In the process is where I discovered the faults, even found a bent axle housing. It has been worth the time to do it.
I don't need to touch the body or interior, so I guess I am about 1000 hours of my labor in it now. Engine rebuilt, tranny rebuilt, everything rebuilt!!!
I thought about it Ray, I'm just not that crafty. I'll be lucky if I can get it welded onto the housing straight!!Regarding the brackets that weld to the rear housing, they are very easy to fab up in your shop. I made my own.
I thought about it Ray, I'm just not that crafty. I'll be lucky if I can get it welded onto the housing straight!!
Yea... I guess I pulled a fast one on her Steve, she still thinks it was the most fun vacation she's ever had!!Hmmm"not very crafty Ricky"
Crafty enough to get that old car to do a long return trip with no issues
Crafty enough to have the missus smiling all the way
Id say your as crafty as required Rick
Steve